DIN EN 61347-2-6 Berichtigung 1-2003 DINEN61347-2-6-2001的技术勘误1

上一篇: DIN EN 61347-2-4 Berichtigung 1-2003 DINEN61347-2-4-2001的技术勘误1
下一篇: DIN EN 60044-2-2003 仪表用互感器.第2部分:电感式电压互感器

Product Code:SAE J2616
Title:Testing Performance of the Fuel Processor Subsystem of An Automotive Fuel Cell System
Issuing Committee:Fuel Cell Standards Committee
Scope:This recommended practice is intended to serve as a design verification procedure and not a product qualification procedure. It may be used to verify design specifications or vendor claims. Test procedures, methods and definitions for the performance of the fuel processor subsystem (FPS) of a fuel cell system (FCS) are provided. Fuel processor subsystems (FPS) include all components required in the conversion of input fuel and oxidizer into a hydrogen-rich product gas stream suitable for use in fuel cells. Performance of the fuel processor subsystem includes evaluating system energy inputs and useful outputs to determine fuel conversion efficiency and where applicable the overall thermal effectiveness. Each of these performance characterizations will be determined to an uncertainty of less than +/- 2% of the value.The method allows for the evaluation of fuel processor subsystems for two general cases.- Compare fuel processors with different designs (e.g., catalytic partial oxidation reforming, autothermal reforming or steam reforming) on a common basis where no specific fuel cell system design has been identified.- Assess the performance of a specific fuel processor in the context of a specific fuel cell system design.This document applies to all fuel processor subsystems for transportation applications regardless of fuel processor type, fuel cell type, electrical power output, thermal output, or system application (propulsion or auxiliary power unit (APU)). For example, the fuel processor subsystems associated with proton exchange, molten carbonate and solid oxide fuel cells can differ due to the requirements of the fuel cells themselves. Performance of the fuel processor subsystem, and preprocessor if applicable, is evaluated. A stand alone fuel processor 驴system驴 or even the primary reactor (e.g., autothermal, partial oxidation or steam reforming reactor) of a fuel processor subsystem that would normally be integrated into a fuel cell system can be evaluated. The fuel processor together with the preprocessor (if required) converts the fuel (gasoline or other liquid hydrocarbon) to a reformate gas consisting largely of H2, CO, CO2, H2O and N2 (if air is used). After the fuel processor subsystem, reformate gas typically contains only trace levels of carbon bearing components higher than C1. The FPS would be evaluated in a test facility that is designed to evaluate a stand-alone component rather than a portion of the reformer such as a specific catalyst or a particular vessel design. Any fuel(s) mutually agreed to by the test parties can be used such as 1) straight run gasoline (EPA Fuel- CARB reformulated gasoline Tier II, 30 ppm sulfur), or 2) methanol or 3) hydrocarbon fuel such as iso-octane, naptha, diesel, liquefied natural gas (LNG) or LPG (propane), etc. The procedures provide a point-in-time evaluation of the performance of the fuel processor subsystem. Steady state and transient (start-up and load-following) performance are included. Methods and procedures for conducting and reporting fuel processor testing, including instrumentation to be used, testing techniques, and methods for calculating and reporting results are provided. The boundary limits for fuel and oxidant input, secondary energy input and net energy output are defined. Procedures for measuring temperature, pressure, input fuel flow and composition, electrical power and thermal output at the boundaries are provided.Procedures for determination of the FPS performance measures such as fuel processor efficiency and cold gas efficiency at a rated load or any other steady state condition are provided. Methods to correct results from the test conditions to reference conditions are provided.SI units are used throughout the recommended practice document.

标准名称：	一次性使用离心杯式血液成分分离器
英文名称：	Blood components separation sets for single use，
中标分类：	医药、卫生、劳动保护 >> 医疗器械 >> 一般与显微外科器械
ICS分类：	医药卫生技术 >> 医疗设备 >> 输血、输液和注射设备
发布部门：	国家食品药品监督管理局
发布日期：	2005-12-07
实施日期：	2006-12-01
首发日期：	1900-01-01
作废日期：	1900-01-01
归口单位：	国家食品药品监督管理局济南医疗器械质量监督检验中心
起草单位：	国家食品药品监督管理局济南医疗器械质量监督检验中心
出版社：	中国标准出版社
出版日期：	2006-01-06
页数：	16开， 页数：22， 字数：37千字
书号：	155066.2-16636

本标准规定了以附录A中图A.10所示的分离杯为主要结构特征的一次性使用离心杯式血液成分分离器(以下简称分离器)的要求，这些分离器与血液成分采集机配套，用于对血液成分的采集、分离、回输、置换和贮存。本标准所规定的分离器主要由分离杯、管路系统和收集系统三部分组成。

没有内容

没有内容

没有内容